SHOP KILN PARTS

A-J-1100/00
$150.00

Corrosion Resistant Aluminized Steel Stand & Legs for use with 6-Sided kilns (like the Doll / Test Kilns)  - The unit is constructed from 14 ga. steel comes with four Legs with PEM Nuts, Hardware for assembly. The stand is 13.65" square and sits 8" off the ground.

A-J-1400/00
$150.00

Corrosion Resistant Aluminized Steel Stand & Legs for use with 7-Sided kilns (like the e14S-3) - The unit is constructed from 14 ga. steel comes with four Legs with PEM Nuts, Hardware for assembly, and pre-installed Hole and Mounting Studs for a vent system. The stand is 15.65" square and sits 8" off the ground.

A-J-14RL/PT
$325.00

L&L's rolling kiln stand features heavy gauge (14 ga) galvannealed steel construction with multiple bends for extra strength, swivel locking casters, and guides for the kiln. Each size is fitted to the kiln. 

A-J-1800/00
$150.00

Corrosion Resistant Aluminized Steel Stand & Legs for use with 8-Sided kilns (like the e18S-3)  - The unit is constructed from 14 ga. steel comes with four Legs with PEM Nuts, Hardware for assembly, and pre-installed Hole and Mounting Studs for a vent system. The stand is 17.8" square and sits 8" off the ground.

A-J-18RL/PT
$325.00

L&L's rolling kiln stand features heavy gauge (14 ga) galvannealed construction with multiple bends for extra strength, swivel locking casters, integrated vent collection box support, and guide rails for the kiln. Each size is fitted to the kiln. 

A-J-2300/00
$150.00

Corrosion Resistant Aluminized Steel Stand & Legs for use with All 10-Sided Kilns - The unit is constructed from 14 ga. steel and comes with four Legs with PEM Nuts, Hardware for assembly, and pre-installed Hole and Mounting Studs for a vent system. The stand is 21.9" square and sits 8" off the ground.

A-J-23RL/PT
$325.00

L&L's rolling kiln stand features heavy gauge (14 ga) galvannealed steel construction with multiple bends for extra strength, swivel locking casters, integrated vent collection box support, and guide rails for the kiln. Each size is fitted to the kiln.

A-J-2900/00
$150.00

Corrosion Resistant Aluminized Steel Stand & Legs for use with All 12-Sided Kilns - The unit is constructed from 14 ga. steel and comes with four Legs with PEM Nuts, Hardware for assembly, and pre-installed Hole and Mounting Studs for a vent system. The stand is 25.7" square and sits 8" off the ground.

A-J-29RL/PT
$325.00

L&L's rolling kiln stand features heavy gauge (14 ga) galvannealed steel construction with multiple bends for extra strength, swivel locking casters, integrated vent collection box support, and guide rails for the kiln. Each size is fitted to the kiln. 

NO IMAGE
A-T-23LC/00
$370.00

DaVinci Lid Channel Set for T2300. Includes the powder-coated channels that go around the lid slab, handles, and all mounting hardware.

NO IMAGE
A-T-34LC/00
$405.00

DaVinci Lid Channel Set for T3400. Includes the powder-coated channels that go around the lid slab, handles, and all mounting hardware.

NO IMAGE
A-X-23LC/00
$310.00

DaVinci Lid Channel Set for X2300. Includes the powder-coated channels that go around the lid slab, handles, and all mounting hardware.

NO IMAGE
A-X-28LC/00
$335.00

DaVinci Lid Channel Set for X2800. Includes the powder-coated channels that go around the lid slab, handles, and all mounting hardware.

NO IMAGE
A-X-32LC/00
$345.00

DaVinci Lid Channel Set for X3200. Includes the powder-coated channels that go around the lid slab, handles, and all mounting hardware.

L-G-6NUT/00
$2.10

#6 Nut and Lock Washer - Set is used to mount the Control Transformer, Power Relay, and Power Terminal Block to the Control Box or Contactor Plate. (Note screw is shown only for illustration)

L-G-SNUT/00
$0.90

#10-24 Stainless Steel Hex Nut - Unit is used for mounting the Vent Bypass Box and Contactor Plates and for the Element Terminal Bolts

L-G-WASH/EU
$0.65

#10 Stainless Steel Flat Fender Washer - This is the large diameter (3/4" OD) washer used to sandwich element ends on the element terminal.

L-X-STND/00
$200.00

Stand for all Standard Voltage Floor Mounted Control Panels - The unit is the bottom stand part of the Floor Mounted Control Panel and is used with All Non-480 Volt Floor Mounted Control Panels on DaVinci and optionally on Jupiter kilns.

M-A-MNT4/00
$0.15

#1/4-20 Nut - Unit is used to attach the Vent Motor to the Wall-Mount Bracket (4 per Vent)

M-A-MNT4/00
$0.15

1/4"-20 Zinc Plated Hex Nut - Unit is the standard Hex Nut for 1/4" Diameter Bolts & Screws and is used in conjuction with Multi-Mounting Brackets and the Mesh Backing of Hercules and Easy-Load kilns.

M-A-MWS4/00
$0.10

#1/4 Lock Washer - Unit is used to attach the Vent Motor to the Wall-Mount Bracket (4 per Vent)

M-A-SMS2/00
$0.15

#10 x 1/2" Long Stainless Steel Sheet Metal Screw - Unit has a Phillips Pan Head and is used to attach Hinge Components to the kiln body and to attach Handles to the kiln body

M-A-SMS4/00
$0.65

#8 x 2-1/2" Long Stainless Steel Sheet Metal Screw - Unit has a Phillips Pan Head and is used to attach Kiln Sitter/Timers and longer Type K Thermocouples (Pyrocil & 8 Gauge Exposed) to the kiln body

M-A-SMS5/00
$0.15

#6 x 1/2" Long Stainless Steel Sheet Metal Screw - Unit has a Phillips Pan Head and is used to attach the Control Board to the Control Panel

M-A-SMS7/00
$0.15

#8 x 3/4" Long Zinc Plated Sheet Metal Screw - Unit has a Phillips Pan Head and is used to attach the Element Cover Box or Control Box to the kiln body, the Power Terminal Block to the Contactor Plate, the Power Terminal Strip and Thermocouple Terminal Strip to the Element Cover Box, and the Safety Chains to the kiln Lid and top Ring

M-A-SMS9/00
$0.65

#8 x 3" Long Stainless Steel Sheet Metal Screw - Unit has a Phillips Pan Head and is used to attach Kiln Sitter/Timers and longer Type K Thermocouples (Pyrocil & 8 Gauge Exposed) to the kiln body

M-G-CNDR/18
$6.50

#8 Lid Safety Chain - Unit is precut to 16" Long, comes with Mounting Hardware, and is used to secure the Kiln Lid to the Top Ring

M-G-CNDR/23
$10.75

#8 Lid Safety Chain - Unit is precut to 28" Long, comes with Mounting Hardware, and is used to secure the Kiln Lid to the Top Ring

M-G-ECBX/HG
$14.75

These are the metal hinges that get attached to the kiln case and mate with the hinge parts that are welded to the element cover boxes. There are two hinge parts and four mounting screws.