L-G-FS40/NL
$30.00
40 Amp Fuse - Unit is used with 250 Volt / 60 Amp Fuse Holders
October 19, 2026
|
|---|
SHOP KILN PARTSPottery Kiln Electric
L-G-FS60/60
$89.00
60 Amp Fuse - Unit is used with 600 Volt / 60 Amp Fuse Holders 
L-G-FS01/NL
$30.00
1 Amp Fuse - Unit is used with the 1 Pole 250 Volt / 30 Amp Fuse Holders 
L-G-FH30/10
$111.00
1 Pole Fuse Holder with a Maximum Load Rating of 250 Volts and 30 Amps 
C-G-SP10/00
$3.10
Cylindrical Ceramic Spacer - Unit is a 3/4" Diameter Cylinder x 1/4" High with a 1/4" Diameter hole in the center. NOTE: These are also used to hold thick elements in place by using it as a wedge between the element and the ceramic holder. See this Knowledgebase page.
L-G-FS15/60
$75.00
15 Amp Fuse - Unit is used with 600 Volt / 30 Amp Fuse Holders
L-G-FS02/NL
$30.00
2 Amp Fuse - Unit is used with the 1 Pole 250 Volt / 30 Amp Fuse Holders 
L-G-FS02/60
$58.00
2 Amp Fuse - Unit is used with 600 Volt / 30 Amp Fuse Holders 
L-G-FH30/20
$75.00
2 Pole Fuse Holder with a Maximum Load Rating of 250 Volts and 30 Amps 
L-G-FH60/20
$89.00
2 Pole Fuse Holder with a Maximum Load Rating of 250 Volts and 60 Amps 
L-G-FH10/20
$111.00
2 Pole Fuse Holder - Unit has a Maximum Load Rating of 250 Volts and 100 Amps. 
L-G-FH30/62
$97.00
2 Pole Fuse Holder - Unit has a Maximum Load Rating of 600 Volts and 30 Amps
L-G-FS20/60
$75.00
20 Amp Fuse - Unit is used with 600 Volt / 30 Amp Fuse Holders 
L-G-FH30/63
$97.00
3 Pole Fuse Holder - Unit has a Maximum Load Rating of 600 Volts and 30 Amps
L-G-FS30/NL
$30.00
30 Amp Fuse - Unit is used with 250 Volt / 30 Amp Fuse Holders
L-G-FS30/62
$75.00
30 Amp Fuse - Unit is used with 600 Volt / 30 Amp Fuse Holders 
L-G-FS50/NL
$30.00
50 Amp Fuse - Unit is used with 250 Volt / 60 Amp Fuse Holders 
L-G-SR50/00
$113.00
50 Amp NEMA 6-50R Single Receptacle - Unit is used with All DaVinci Panels at 240 Volts or 208 Volts and any Phase Power
L-G-FS60/NL
$30.00
60 Amp Fuse - Unit is used with 250 Volt / 60 Amp Fuse Holders 
L-G-FS70/NL
$58.00
70 Amp Fuse - Unit is used with 250 Volt / 100 Amp Fuse Holders
L-G-FS90/NL
$58.00
90 Amp Fuse - Unit is used with 250 Volt / 100 Amp Fuse Holders 
L-G-ELTR/00
$63.00
Ceramic Element Terminal Block for Easy-Load kilns. (NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Nov 1, 2025) - newer kilns need this block. Check your kiln before ordering. The unit includes the terminal screw, nuts, and stainless flat washers. Lock washers are no longer needed. You may also need two mounting screws. See this link for wiring help (diagrams at the bottom of page) 
L-G-MTRM/00
$57.00
Ceramic Element Terminal Block for M Series (middle section) Easy-Fire Kiln Sections. Used in production until approximately Feb 1, 2025 on e18M, e18M-3, e23M, e23M-3, e28M-3 middle kiln sections that are 4.5" high. M-Model kilns built after approximately Feb 1, 2025 use the universal terminal block. CHECK YOUR KILN BEFORE ORDERING. The new universal terminal block is not capable of replacing this block on a kiln. The unit includes the terminal screws, nuts, and stainless flat washers. Lock washers are no longer needed. You may also need two mounting screws. See this link for wiring help (diagrams at the bottom of page) 
L-J-BK29/CE
$54.00
Ceramic Element Terminal Block for Kiln Sections with Three Elements - Unit includes two Terminal Screw Assemblies. (NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Sep 1, 2024) - newer kilns need this block. Check your kiln before ordering. You may also need two mounting screws See this link for wiring help (diagrams at the bottom of page) 
L-J-BKDL/CE
$63.00
Ceramic Element Terminal Block for Kiln Sections with Three Elements - Unit includes four Terminal Screw Assemblies. (NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Sep 1, 2024) - newer kilns need this block. Check your kiln before ordering. You may also need two mounting screws See this link for wiring help (diagrams at the bottom of page) 
L-J-BK18/CE
$62.00
This older version of our Ceramic Element Terminal Block has been discontinued and directly replaced with two of these NEW BLOCKS for every one of the old block. If your old block has 3 bolts (series configuration, as pictured) then you need to order one of these jumper wires as well. You will also need 4 of these screws (2 per NEW BLOCK). Reference the diagrams at the bottom of this page for wiring your new blocks based on whether you have parallel or series elements. 
L-J-BK23/CE
$53.00
This older version of our Ceramic Element Terminal Block has been discontinued and directly replaced with two of these NEW BLOCKS for every one of the old block. If your old block has 2 bolts (parallel configuration, as pictured) then you need to order two of these jumper wires as well. You will also need 4 of these screws (2 per NEW BLOCK). Reference the diagrams at the bottom of this page for wiring your new blocks based on whether you have parallel or series elements. 
L-G-FS05/00
$3.45
1/2 Amp Control Panel Fuse 
L-G-TR24/00
$64.00
12 VA Control Transformer - Unit is used on most kilns with Three or Fewer Relays 
L-G-TR24/LG
$70.00
30 VA Control Transformer - Unit is used on Polygonal Kilns with Four or More Relays and on All DaVinci Kilns 
L-G-PCCP/00
$18.25
Clamp to hold on 50 Amp Power Cord. This clamp hold the power cord in place where the cord comes out of the control panel. 
L-G-CRBS/00
$14.00
Cord Bushing for Small Cords 
L-G-DVCC/KT
$69.00
This is a set of components to move the cord connections on a DaVinci kiln ring to the outer element connection box. The kit consists of:
L-G-SWDR/00
$106.00
Door Activated Element Shut-Off Limit Switch for Easy-Load & Hercules Includes wire that goes to control panel. 
L-G-PB2P/EF
$50.00
2 Pole Power Terminal Block - Unit is used on All Easy-Fire Kilns at any Voltage and 1 Phase Power. These are also used for 380-415/3 Phase Wye kilns that have a neutral by using two of them to create four connections. 
L-G-PB3P/EF
$63.00
2 Pole Power Terminal Block - Unit is used on All Easy-Fire Kilns at any Voltage and 3 Phase Power 
L-G-BK24/00
$35.00
24" Long piece of the red Element Board Material that is 1-1/4" Wide and 1/8" Thick 
L-G-INSM/00
$5.60
Element Insulator Bushing - Unit is used in conjunction with the Old Style (Red) Element Terminal Boards to keep the Element insulated from the Sheet Metal Casing Internal Reference: C-BSH-C1620X-B1, C-BSH-C1620X-A1 
L-G-INTB/00
$6.05
Corderiete Ceramic Tube: Element Insulator Tube - 4" long 5/16" OD x 3/1"6 ID. Used in some front-loading kilns for insulated the element ends as they protrude throught he insulation. 
L-G-ESSW/40
$239.00
40 Amp Element Power Cut Off Switch - Unit is used with Easy-Fire EU kilns and Positive Door Interlock Switch (European Style) Option 
L-G-SWCF/00
$111.00
15 Amp Element Power Cut Off Microswitch - Unit is used with All Fuego and Robin Kilns at any Voltage and Phase Power 
M-G-TSET/00
$7.50
Hardware Set for one Element Connection on a Ceramic Element Terminal Block. Set includes:
Note: You may not need all the fender washers depending on your situation. NOTE: This part set is available for 50% discount when ordered with elements. Note: These assemblies used to include lock washers, but they are no longer necessary. 
M-G-TSET/LG
$7.50
Hardware Set for one Element Connection on a fabricated electrically insulating board (See this example) Set includes:
Note: You may not need all the fender washers. NOTE: This part set is available for 50% discount when ordered with elements. 
L-G-RL25/12
$54.00
25 Amp Enclosed Power Relay with a 12 Volt Coil Unit is the standard Power Relay used on Easy-Fire, Plug-n-Fire, eQuad-Pro, Doll, Jupiter, eFL Series, and X2300 & XB2300 Control Panels, it is also used as the Control Relay for X2800-D & XB2800-D, X3200-D & XB3200-D, T2300-D & TB2300-D, and T3400-D & TB3400-D Series DaVinci Kilns and Easy-Load kilns. This contactor is used interchangeably as a power contactor on both 240-volt and 208-volt kilns.
L-G-RL25/30
$64.00
25 Amp Enclosed Power Relay with a 240 Volt Coil - used on some older manual kilns that require power relays and as a control relay from some 480 volt kilns See this page for the 12 Volt 25 Amp relay we use for most kilns. 
M-A-SMEL/10
$0.40
Hex Head #10 2-1/2 Self-Tapping Screw for mounting EL Terminal Blocks, Stainless 400 Series 
S-G-CACL/00
$10.10
Snap-in Cable Clamp used to secure 15 and 20 amp Jumper Cords in the Element Cover Box 
S-G-CACL/SM
$5.20
Snap-in Cable Clamp used to secure the control cord on the Handheld DynaTrol Box 
S-G-BUSH/LG
$5.20
Heyco Snap-in Bushing Large 3/4" - This bushing is used to protect the thermocouple wires on a Jupiter Kiln as they run through the Mounting Brackets on the control panel. 
S-G-BUSH/SM
$3.30
Small Heyco Snap-in Bushing for 3/8" holes |
