L-G-SWCF/00
$111.00
15 Amp Element Power Cut Off Microswitch - Unit is used with All Fuego and Robin Kilns at any Voltage and Phase Power
August 22, 2026
|
|---|
SHOP KILN PARTSPottery Kiln Electric
M-G-TSET/00
$7.50
Hardware Set for one Element Connection on a Ceramic Element Terminal Block. Set includes:
Note: You may not need all the fender washers depending on your situation. NOTE: This part set is available for 50% discount when ordered with elements. Note: These assemblies used to include lock washers, but they are no longer necessary. 
M-G-TSET/LG
$7.50
Hardware Set for one Element Connection on a fabricated electrically insulating board (See this example) Set includes:
Note: You may not need all the fender washers. NOTE: This part set is available for 50% discount when ordered with elements. 
L-G-RL25/12
$54.00
25 Amp Enclosed Power Relay with a 12 Volt Coil Unit is the standard Power Relay used on Easy-Fire, eQuad-Pro, Doll, Jupiter, eFL Series, and X2300 & XB2300 Control Panels, it is also used as the Control Relay for X2800-D & XB2800-D, X3200-D & XB3200-D, T2300-D & TB2300-D, and T3400-D & TB3400-D Series DaVinci Kilns and Easy-Load kilns. This contactor is used interchangeably as a power contactor on both 240-volt and 208-volt kilns.
L-G-RL25/30
$64.00
25 Amp Enclosed Power Relay with a 240 Volt Coil - used on some older manual kilns that require power relays and as a control relay from some 480 volt kilns See this page for the 12 Volt 25 Amp relay we use for most kilns. 
M-A-SMEL/10
$0.40
Hex Head #10 2-1/2 Self-Tapping Screw for mounting EL Terminal Blocks, Stainless 400 Series 
S-G-CACL/00
$10.10
Snap-in Cable Clamp used to secure 15 and 20 amp Jumper Cords in the Element Cover Box 
S-G-CACL/SM
$5.20
Snap-in Cable Clamp used to secure the control cord on the Handheld DynaTrol Box 
S-G-BUSH/LG
$5.20
Heyco Snap-in Bushing Large 3/4" - This bushing is used to protect the thermocouple wires on a Jupiter Kiln as they run through the Mounting Brackets on the control panel. 
S-G-BUSH/SM
$3.30
Small Heyco Snap-in Bushing for 3/8" holes 
L-J-INF0/30
$62.00
240 Volt Infinite Zone Switch - Unit includes a Mounting Nut. This can be used for both 240V and 208V Kilns. NOTE: Often a switch, when it burns out, exhibits overheating on the switch body at one of the spade electrical connection points. When this occurs, the mating connector on the wire may not give good electrical contact if refused. To reduce the possibility of overheating at this point on the new switch, we recommend replacing the female connector and the wire attached to it. If the switch body looks O.K. then do not replace the female wire connectors. NOTE CONCERNING 208V SWITCHES When used on a 208 volt kiln the timing of th heater will be slightly different than when used on a 240 volt kiln. We no longer supply 208 volt switches. NO IMAGE
L-J-PB00/01
$33.00
Old Style Power Connection Board with Terminal Bolts - Unit is used on Older Econo J1400, J1800, J23, and J230 Series Kilns at any Voltage and 1 Phase Power 
L-J-DR00/00
$54.00
15 Amp Double Receptacle - Unit is used for Older Econo J1400, J1800, and J2300 Series Kilns at any Voltage and Phase Power 
L-J-SR15/00
$46.00
15 Amp Single Receptacle - Unit is used for Older Econo J1400, J1800, and J2300 Series Kilns at any Voltage and Phase Power 
L-J-DR29/00
$68.00
20 Amp Double Receptacle - Unit is used for Older Econo J2900 Series Kilns at any Voltage and Phase Power 
L-J-PB29/01
$31.00
Old Style Power Connection Board with Terminal Bolts - Unit is used on Older Econo J236, J45, and J2900 Series Kilns at any Voltage and 1 Phase Power 
L-J-SR20/00
$56.00
20 Amp Single Receptacle - Unit is used for All Newer Jupiter Automatic and Jupiter Manual Kilns at any Voltage and Phase Power. 6-20R Also used on the Plug-n-Fire PF8 panel. 
L-G-EPTR/00
$18.25
Power Terminal Strip - Unit has Two 1/4" Spade Terminals on each side and is used for the Power Wires on Liberty-Belle Kilns 
L-G-MOV1/00
$15.75
MOV Surge Suppressor for 250 Volt / 50 Amp Enclosed Power Contactors - Unit is 5mm in Diameter, absorbs the discharge energy from the inductive coil of a contactor, and can be used on All 240 Volt or 208 Volt Contactors The L-G-MOV1/00 MOV has a mark on it of PZ390 (you have to use a magnifying glass to see this). Attach the MOV Suppressor to the Power Contactor by using two 16-14 AWG Insulated Female Slip on Wire Terminals for 1/4" Spades, one on each end of the MOV. 
L-G-RFFT/00
$86.00
Noise Filter for Radio Frequency Noise - This is used to filter incoming power to prevent line noise from affecting the electronic control 
L-J-TBKT/00
$11.00
Mounting Kit for Old Style (Red) Element Terminal Boards - Kit includes six 1/4" high ceramic spacers and two #8 x 1-1/2" long stainless sheet metal screws. 
L-J-PBMT/01
$12.50
Mounting Kit for Old Style (Red) Power Connection Boards - Kit includes all Hardware 
L-G-SWCH/00
$122.00
L-G-SWTG/00
$33.00
On/Off Toggle Switch - Unit is used to switch the Control Board on and off on All Automatic Kilns 
L-G-SWTG/PL
$3.90
Toggle Switch Legend Plate - Unit is used in conjunction with All On/Off Toggle Switches 
L-G-FSPB/30
$56.00
30 Amp Panel Mount Fuse Holder for BAN 
L-G-FSPB/00
$28.00
1/2 Amp Panel Mount Fuse Holder for Control Fuse 
L-G-PBLG/01
$77.00
2 Pole Power Connection Block - Units is rated for 175 Amps and is used with All Jupiter Automatic and Jupiter Manual Kilns at any Voltage and 1 Phase Power 
L-G-PBLG/02
$86.00
3 Pole Power Connection Block - Units is rated for 175 Amps and is used with All Jupiter Automatic and Jupiter Manual Kilns at any Voltage and 3 Phase Power 
L-G-PBLG/05
$177.00
1 Pole Power Connection Block - Unit is rated for 335 Amps and is used with DaVinci Kilns at 480 Volts or 380 Volts and 3 Phase Power that require an extra Power Connection 
L-G-PBLG/03
$283.00
3 Pole Power Connection Block - Unit is rated for 335 Amps and is used with DaVinci Kilns at any Voltage and Phase Power 
L-G-RL30/20
$127.00
2 Pole Power Relay - Unit is rated for 30 Amps (resistive load below 300 Volts) with a 208 Volt Coil and is used in Older Manual Kilns and Renaissance Kilns at 208 Volts and any Phase Power
L-G-RL30/30
$127.00
2 Pole Power Relay - Unit is rated for 30 Amps (resistive load under 300 volts) with a 240 Volt Coil and is used in Older Manual Kilns and Renaissance Kilns at 240 Volts and any Phase Power 
L-G-RL50/62
$216.00
3 Pole Power Relay - Unit is rated for 50 Amps with a 120 Volt Coil - Unit is the standard Power Relay on All X2800-D & XB2800-D, X3200-D & XB3200-D, T2300-D & TB2300-D, and T3400-D & TB3400-D Series DaVinci Kilns and Easy-Load kilns that are rated for 480 volts. (Note: the 480 volt input current is reduced to 120 volts for the control circuit that controls the coils of these contactors)
L-G-RL50/30
$216.00
3 Pole Power Relay - Unit is rated for 50 Amps with a 240/208 Volt Coil - Unit is the standard Power Relay on All X2800-D & XB2800-D, X3200-D & XB3200-D, T2300-D & TB2300-D, and T3400-D & TB3400-D Series DaVinci Kilns and Hercules and Easy-Load kilns. These are used on kilns that have either 208 or 240 volt power. 
L-G-PB2P/EQ
$55.00
2 Pole Power Terminal Block - Unit is used on all eQuad and eFL kilns at any Voltage and 1 or 3 Phase Power (two used for 3 Phase). These are also used for 380-415/3 Phase Wye kilns that have a neutral by using two of them to create four connections. 
L-G-TRPW/EF
$33.00
Power Terminal Strip - Unit has Six 1/4" Spade Terminals on each side, comes with a Terminal Strip Marker Board and is used for the Power Wires on drop-down Control Panels 
L-G-GLUG/70
$11.25
SLU-70 Copper Lug used to ground an electrical circuit 
L-G-TERM/LG
$1.60
#10-24 Stainless Steel Element Terminal Bolt - Unit is 1-1/4" Long and is used for all L&L kilns. Note: past lengths used were 1-1/2" and 1-3/4" long. This is a direct replacement and should work in all situations. 
L-G-WASH/EU
$0.75
#10 Stainless Steel Flat Fender Washer - This is the large diameter (3/4" OD) washer used to sandwich element ends on the element terminal.
L-G-TRTC/EF
$33.00
Thermocouple Terminal Strip - Unit has Six 3/16" Spade Terminals on each side, comes with a Terminal Strip Marker Board and is used for the Thermocouple Wires on drop-down Control Panels
L-G-BKUN/CE
$33.00
Unit includes one block and two Terminal Screw Assemblies. You may also need two mounting screws You may also need this or this jumper wire. See this link for wiring help (diagrams at the bottom of page) 
L-G-BLKK/IT
$64.00
For replacing broken old standard blocks on your kiln with the new blocks. Includes the following: 4 x Mounting Screws 
L-G-SNUT/00
$1.10
#10-24 Zinc-Plated Hex Nut - Unit is used for mounting the Vent Bypass Box, Contactor Plate in the Control Panel, and for the Element Terminal Bolts |
