One gallon of K23 firebrick dust for use in repair purposes. Comes in four plastic quart jars.

One quart of K23 firebrick dust for use in repair purposes. Comes in a plastic jar with a screw-on lid.

One half pint of K23 firebrick dust for use in repair purposes. Comes in a plastic jar with a screw-on lid.

When you need to convert your kiln from Type K to Type S thermocouples, this plug is cemented into the larger hole we use for our Type K thermocouples with protection tubes.

• Video tutorial 

Includes the following

½ pint Primer Mix
½ pint Brick Dust
½ pint Brick Facing
½ pint Brick Cement
1 brick
Small Plastic Spatula
Small brush
1 rubber glove
1 small sponge

Instructions

This is used to prevent element ends from touching each other (on older kilns). A 21/64" diameter hole is drilled into the brick 1-1/4" deep and the assembly is inserted into the hole. The overall length is 2" and the thick end is about 3/4" long.

Ceramic Element Terminal Block for Easy-Load kilns.

(NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Nov 1, 2025) - newer kilns need this block. Check your kiln before ordering. 

The unit includes the terminal screw, nuts, and stainless flat washers. Lock washers are no longer needed.

You may also need two mounting screws.

See this link for wiring help (diagrams at the bottom of page)

Ceramic Element Terminal Block for M Series (middle section) Easy-Fire Kiln Sections. Was used on e18M, e18M-3, e23M, e23M-3, e28M-3 middle kiln sections that are 4.5" high.

(NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Feb 1, 2025) - newer kilns need this block. Check your kiln before ordering. 

The unit includes the terminal screws, nuts, and stainless flat washers. Lock washers are no longer needed.

You may also need two mounting screws.

See this link for wiring help (diagrams at the bottom of page)

Ceramic Element Terminal Block for Kiln Sections with Three Elements - Unit includes two Terminal Screw Assemblies.

(NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Sep 1, 2024) - newer kilns need this block. Check your kiln before ordering. 

You may also need two mounting screws

See this link for wiring help (diagrams at the bottom of page)

Ceramic Element Terminal Block for Kiln Sections with Three Elements - Unit includes four Terminal Screw Assemblies.

(NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Sep 1, 2024) - newer kilns need this block. Check your kiln before ordering. 

You may also need two mounting screws

See this link for wiring help (diagrams at the bottom of page)

This older version of our Ceramic Element Terminal Block has been discontinued and directly replaced with two of these NEW BLOCKS for every one of the old block.

If your old block has 3 bolts (series configuration, as pictured) then you need to order one of these jumper wires as well. 

You will also need 4 of these screws (2 per NEW BLOCK). 

Reference the diagrams at the bottom of this page for wiring your new blocks based on whether you have parallel or series elements.

This older version of our Ceramic Element Terminal Block has been discontinued and directly replaced with two of these NEW BLOCKS for every one of the old block.

If your old block has 2 bolts (parallel configuration, as pictured) then you need to order two of these jumper wires as well. 

You will also need 4 of these screws (2 per NEW BLOCK). 

Reference the diagrams at the bottom of this page for wiring your new blocks based on whether you have parallel or series elements.

Zinc Plated Chest Handle - Unit is 3-1/2" Wide, includes Mounting Hardware and is used on All Easy-Fire Kiln, eQuad-Pro Kiln, School-Master Kiln, DaVinci Kiln, and Dura-Fire Kiln Sections

Clamp to hold on 50 Amp Power Cord. This clamp hold the power cord in place where the cord comes out of the control panel.

Corrosion Resistant Aluminized Steel Stand & Legs for use with All 10-Sided Kilns - The unit is constructed from 14 ga. steel and comes with four Legs with PEM Nuts, Hardware for assembly, and pre-installed Hole and Mounting Studs for a vent system. The stand is 21.9" square and sits 8" off the ground.

Corrosion Resistant Aluminized Steel Stand & Legs for use with All 12-Sided Kilns - The unit is constructed from 14 ga. steel and comes with four Legs with PEM Nuts, Hardware for assembly, and pre-installed Hole and Mounting Studs for a vent system. The stand is 25.7" square and sits 8" off the ground.

Corrosion Resistant Aluminized Steel Stand & Legs for use with 6-Sided kilns (like the Doll / Test Kilns)  - The unit is constructed from 14 ga. steel comes with four Legs with PEM Nuts, Hardware for assembly. The stand is 13.65" square and sits 8" off the ground.

Corrosion Resistant Aluminized Steel Stand & Legs for use with 7-Sided kilns (like the e14S-3) - The unit is constructed from 14 ga. steel comes with four Legs with PEM Nuts, Hardware for assembly, and pre-installed Hole and Mounting Studs for a vent system. The stand is 15.65" square and sits 8" off the ground.

Corrosion Resistant Aluminized Steel Stand & Legs for use with 8-Sided kilns (like the e18S-3)  - The unit is constructed from 14 ga. steel comes with four Legs with PEM Nuts, Hardware for assembly, and pre-installed Hole and Mounting Studs for a vent system. The stand is 17.8" square and sits 8" off the ground.

Complete 2nd Generation Spring-Assisted Easy-Lift Hinge for 10-Sided Kilns - Assembly includes all 2nd generation Easy-Lift Hinge components: hinge body and lid metal, mounting hardware, springs, bars. Can be used on all 10-Sided Kilns with two or more sections.

This stainless steel hinge assembly can be used to replace the older 1st generation aluminized steel hinge assemblies. You need to replace the entire assembly. See this video for how to replace the hinge assembly.

See how to install the Spring Hinge

See how to adjust the Spring Hinge

See how to adjust spring tension on the Spring Hinge

Complete 2nd Generation Spring-Assisted Easy-Lift Hinge for 12-Sided Kilns - Assembly includes all 2nd generation Easy-Lift Hinge components: hinge body and lid metal, mounting hardware, springs, bars. Can be used on all 12-Sided Kilns with two or more sections.

This stainless steel hinge assembly can be used to replace the older 1st generation aluminized steel hinge assemblies. You need to replace the entire assembly. See this video for how to replace the hinge assembly.

See how to install the Spring Hinge

See how to adjust the Spring Hinge

See how to adjust spring tension on the Spring Hinge

Complete Standard Non-Spring Hinge - Unit includes All Hinge Components, Mounting Hardware, Safety Chain, and can be used on All 6-Sided, 8-Sided, or 10-Sided Kilns

Control Panel for Jupiter Kilns with 3 Zones or fewer - Unit has a corrosion resistant powder coated finish and is designed with a hinged door. It either mounts directly on your kiln's element boxes, or on a floor stand (sold separately). 

1/2 Amp Control Panel Fuse

12 VA Control Transformer - Unit is used on Polygonal Kilns with Three or Fewer Relays

30 VA Control Transformer - Unit is used on Polygonal Kilns with Four or More Relays and on All DaVinci Kilns

Control Wire Harness - All wires precut and terminated. 

All wires are color coded and the color coding corresponds to the wiring diagram

Control Wire Harness - Set of wires is precut and terminated for all three section Easy-Fire kilns.

Control Wire Harness - Set of wires is precut and terminated for all three section School-Master Kilns (SM23T, SM23T-3 & SM28T-3).

Control Wire Harness - Set of wires is precut and terminated for all Easy-Fire Kilns with two Sections.

Cord Bushing for Small Cords

Corner Brick for e2818-XT & e2827-XT Kilns. There are four pieces required per kiln section. They have two element groove cut-outs.