Lid Latch Set for 2nd Generation Easy-Lift Hinges - Unit includes the Clasp, Hook, and Mounting Hardware

Lid Mount for 10-Sided Kiln 2nd Generation Easy-Lift Hinges - Unit includes Mounting Hardware

Lid Mount for 12-Sided Kiln 2nd Generation Easy-Lift Hinges - Unit includes Mounting Hardware.

Locking Push Pin Assembly for 2nd Generation Easy-Lift Hinges - Unit includes Mounting Hardware and is used with All Easy-Lift Spring Hinges to ensure that the lid does not accidently close

Right Spring for 10-Sided Kiln 2nd Generation Easy-Lift Hinges

(Note the thickness of the spring wire is .285" vs .316" diameter for the 12 sided kiln hinge spring)

Right Spring for 12-Sided Kiln 2nd Generation Easy-Lift Hinges

(Note the thickness of the spring wire is .316" vs .285" diameter for the 10 sided kiln hinge spring)

Ring Mount for 10-Sided Kiln 2nd Generation Easy-Lift Hinges - Unit includes Mounting Hardware

Ring Mount for 12-Sided Kiln 2nd Generation Easy-Lift Hinges - Unit includes Mounting Hardware

These are the metal hinges that get attached to the kiln case and mate with the hinge parts that are welded to the element cover boxes. There are two hinge parts and four mounting screws.

40 Amp Element Power Cut Off Switch - Unit is used with Easy-Fire EU kilns and Positive Door Interlock Switch (European Style) Option

Hardware Set for one Element Connection on a Ceramic Element Terminal Block.

Set includes:

1. One #10-24 x 1-1/4" Long Stainless Steel Bolt
2. Two #10-24 Stainless Steel Nuts
3. Four #10 Fender Washers

Note: You may not need all the fender washers depending on your situation.

NOTE: This part set is available for 50% discount when ordered with elements.

Note: These assemblies used to include lock washers, but they are no longer necessary. 

See this link for wiring help

25 Amp Enclosed Power Relay with a 12 Volt Coil

Unit is the standard Power Relay used on Easy-Fire, eQuad-Pro, Doll, Jupiter, eFL Series, and X2300 & XB2300 Control Panels, it is also used as the Control Relay for X2800-D & XB2800-D, X3200-D & XB3200-D, T2300-D & TB2300-D, and T3400-D & TB3400-D Series DaVinci Kilns and Easy-Load kilns.

This contactor is used interchangeably as a power contactor on both 240-volt and 208-volt kilns. 

See this video for how to check relays.

See this video for how to change relays.

10 Pack - Yellow Insulated Female Slip on Wire Terminal - Unit can accommodate up to 10-12 AWG and a 1/4" Spade, and is used on the Power Wires. (REF: E-TRM-640907-A4) 

Typical use is on power wires that go from relays to terminal strips and from terminal strips to elements.

10 Pack - Blue Insulated Female Slip on Wire Terminal - Unit can accommodate up to 16-14 AWG and a 1/4" Spade, and is used on the Control Board, On/Off Switch, and Relays. (REF: E-TRM-640905-A3)

Blue Insulated Female Slip on Wire Terminal - Unit can accommodate up to 16-14 AWG and a 3/16" Spade, and is used on the Transformer Wiresand 1/2 Amp Panel Control Fuse Holder. (REF: E-TRM-640919-A3)

10 Pack Red Insulated Female Slip on Wire Terminal - Unit can accommodate up to 22-18 AWG and a 3/16" Spade, and is used on the Thermocouple Wires. (REF: E-TRM-640917-A1)

Genesis 2.0 Touch Screen Control Board. You can replace your DynaTrol with this control board. See this link for the features.

Ground Wire Jumper for Piggybacked Control Panels, such as Easy-Fire and eQuad kilns - Unit is 10 AWG, precut, and comes with two Ring Terminals

Hardware for Attaching Stand Legs with PEM Nuts - Includes eight 1/4" Long #20 (1/4-20) Bolts.

Heyco Snap-in Bushing Large 3/4" - This bushing is used to protect the thermocouple wires on a Jupiter Kiln as they run through the Mounting Brackets on the control panel.

One Gallon of Hi-Temp Cement - This is the same Hi-Temp Brick Cement used to cement Lids and Bases together during production. Comes in four plastic quart jars with screw-on lids.

One Quart of Hi-Temp Cement - This is the same Hi-Temp Brick Cement used to cement Lids and Bases together during production. Comes in a plastic jar with a screw-on lid.

1/2 Pint of Hi-Temp Cement - This is the same Hi-Temp Brick Cement used to cement Lids and Bases together during production. Comes in a plastic jar with a screw-on lid.

Cotter Pins for All Hinge Bars - Unit includes a set of two Pins

Hinge Bar for Standard Non-Spring Hinge - Unit is 3/8" in Diameter, 10" in Length, Chrome Plated, and includes two Cotter Pins

Dynatrol Instruction Label - This label goes underneath the DynaTrol Control Board and provides step-by-step instructions for its use

Kit includes six each of 1/2", 1", 2", 4", 6", & 8" high 1-1/2" Square Ceramic Posts

#8 Lid Safety Chain - Unit is precut to 28" Long, comes with Mounting Hardware, and is used to secure the Kiln Lid to the Top Ring

#8 Lid Safety Chain - Unit is precut to 16" Long, comes with Mounting Hardware, and is used to secure the Kiln Lid to the Top Ring

Mounting Kit for Long Type K Thermocouples - Kit includes two #8 3" Screws, six 1/2" high Ceramic Spacers, and is used for all Pyrocil Type K and all Long 8 Gauge Type K (Exposed) Thermocouples

Mullite Thermocouple Protection Tube - Unit is 5" Long x 1" Diameter with a stepped head for use with All Standard Length Type-K 8 Ga. Thermocouples. NOTE: This is the newer type open end tube which was put in service with new kilns starting in September 2020.

Non-Refractory-Ceramic Fiber Paper Insulator - Unit is supplied by the foot with 9" High x 1/8" Thick Dimensions

Non-Refractory-Ceramic Fiber Blanket Insulator - Unit is supplied with 2' Wide x 1' High x 1" Thick Dimensions

On/Off Toggle Switch - Unit is used to switch the Control Board on and off on All Automatic Kilns

Toggle Switch Legend Plate - Unit is used in conjunction with All On/Off Toggle Switches

1/2 Amp Panel Mount Fuse Holder for Control Fuse

Ceramic Peep Hole Plug - Unit is a 1" Diameter x 5" Long Top Hat Style Plug (Stepped Head has a 2" Diameter and serves as a heat lock)

Ceramic Peep Hole Plug - Unit is a approximately 7/8" Diameter (.86") x 3.75" Long Top Hat Style Plug (Stepped Head has a 1.5" Diameter and serves as a heat lock)

50 Amp NEMA 6-50P Power Cord - Unit is a 72" Long Cord with a Three Prong Plug and is used with all Easy-Fire Kilns at any Voltage and 1 Phase Power, all J1800 & JD1800, J23 & JD23, and J230 & JD230 Kilns, and many other kilns at any Voltage and 1 Phase Power (Also used for retrofit on Older Econo J1400 Series Kilns).

Wires are 105 Deg C rated with two 6 gauge wires and one 8 gauge ground wire.

30 Amp NEMA 10-30P Power Cord - The unit is 12' Long with a Three Prong Plug and can be used with any kiln that is 24 amps or below and is 208 or 240 volts and single phase

50 Amp NEMA 14-50P Power Cord - The unit is 12' Long with a Four Prong Plug and can be used with any kiln that is 48 amps or below and is 208 or 240 volts and single phase

50 Amp NEMA 6-50P Power Cord - Unit is 12' Long with a Three Prong Plug and can be used with any kiln that is 48 amps or below and is 208 or 240 volts and single phase

50 Amp NEMA 15-50P Power Cord - Unit is a 72" Long Cord with a Four Prong Plug and is used with All Easy-Fire Kilns at any Voltage and 3 Phase Power and All J1800 & JD1800, J23 & JD23, and J230 & JD230 Kilns at any Voltage and 3 Phase Power