Automatic DynaTrol Control Panel with one 20 Amp Plug-In Circuits and No Branch Fusing - Unit includes a Power Cord is used with DL11-D and DLH11-D Kilns at 120 Volts, 1 Phase power, and under 20 Amps
SHOP FOR L&L KILN PARTS
SUBCATEGORIES
Automatic DynaTrol Control Panel with one 20 Amp Plug-In Circuits and No Branch Fusing - Unit includes a 240 volt Power Cord. Used with DL11-D and DLH11-D Kilns at 208 to 240 Volts, 1 Phase power, and under 20 Amps.

Automatic DynaTrol Control Panel with three 20 Amp Plug-In Circuits and No Branch Fusing - Unit includes a Power Cord is used with JD18, JD23, JD23-PB, JD18X, & JD230 Kilns at 208 Volts or 240 Volts, 1 Phase power, and under 50 Amps

Automatic DynaTrol Control Panel with three 20 Amp Plug-In Circuits and No Branch Fusing - Unit includes a Power Cord is used with JD18, JD23, JD23-PB, JD18X, & JD230 Kilns at 208 Volts or 240 Volts, 3 Phase power, and under 50 Amps

Automatic DynaTrol Control Panel with three 20 Amp Plug-In Circuits and with Branch Fusing - Unit does not include a Power Cord and is used with JD2918, JD2918-PB, JD2927, X1818-D, X1827-D, & X2327-D Kilns at 208 Volts or 240 Volts and 1 Phase power

Automatic DynaTrol Control Panel with three 20 Amp Plug-In Circuits and with Branch Fusing - Unit does not include a Power Cord and is used with JD2918, JD2918-PB, JD2927, X1818-D, X1827-D, & X2327-D Kilns at 208 Volts or 240 Volts and 3 Phase power

Automatic DynaTrol Control Panel with four 20 Amp Plug-In Circuits and with Branch Fusing - Unit does not include a Power Cord and is used with JD236, JD2936, & X2336-D Kilns at 208 Volts or 240 Volts and 1 Phase power

Automatic DynaTrol Control Panel with four 20 Amp Plug-In Circuits and with Branch Fusing - Unit does not include a Power Cord and is used with JD236, JD2936, & X2336-D Kilns at 208 Volts or 240 Volts and 3 Phase power



Complete Easy-Fire Control Panel with all Components and Wiring and cord up to but not including the Element Connection Terminal Blocks - Unit is used with Two Section Easy-Fire Kilns at 208 Volts or 240 Volts and 1 Phase Power

Complete Easy-Fire Control Panel with all Components and Wiring and cord up to but not including the Element Connection Terminal Blocks - Unit is used with Two Section Easy-Fire Kilns at 208 Volts or 240 Volts and 3 Phase Power

Complete Easy-Fire Control Panel with all Components and Wiring and cord up to but not including the Element Connection Terminal Blocks - Unit is used with Three Section Easy-Fire Kilns at 208 Volts or 240 Volts and 1 Phase Power

Complete Easy-Fire Control Panel with all Components and Wiring and cord up to but not including the Element Connection Terminal Blocks - Unit is used with Three Section Easy-Fire Kilns at 208 Volts or 240 Volts and 3 Phase Power


Red Pilot Light - Unit is used for All Manual Kiln Control Panels

Noise Filter for Radio Frequency Noise - This is used to filter incoming power to prevent line noise from affecting the electronic control

Thermocouple Terminal Strip - Unit has Six 3/16" Spade Terminals on each side, comes with a Terminal Strip Marker Board and is used for the Thermocouple Wires on piggybacked Control Panels

240 Volt Infinite Zone Switch - Unit includes a Mounting Nut. This can be used for both 240V and 208V Kilns.
NOTE: Often a switch, when it burns out, exhibits overheating on the switch body at one of the spade electrical connection points. When this occurs, the mating connector on the wire may not give good electrical contact if refused. To reduce the possibility of overheating at this point on the new switch, we recommend replacing the female connector and the wire attached to it. If the switch body looks O.K. then do not replace the female wire connectors.
NOTE CONCERNING 208V SWITCHES
When used on a 208 volt kiln the timing of th heater will be slightly different than when used on a 240 volt kiln. We no longer supply 208 volt switches.
Complete School-Master Control Panel with all Components and Wiring up to but not including the Element Connection Terminal Blocks - Unit is used with Three Section School-Master Kilns at 208 Volts or 240 Volts and 1 Phase Power
Complete School-Master Control Panel with all Components and Wiring up to but not including the Element Connection Terminal Blocks - Unit is used with Three Section School-Master Kilns at 208 Volts or 240 Volts and 3 Phase Power
Automatic DynaTrol Control Panel with two 50 Amp Plug-In Circuits and with Branch Fusing. Includes DynaTrol, panel, stand for panel, fuses, relays, power contactors, transformer and all other internal components.
Unit does not include a Power Cord.
This is used with all Two CIrcuit DaVinci X2800-D & XB2800-D, X3200-D & XB3200-D, T2300-D & TB2300-D, and T3400-D & TB3400-D Series Kilns at 208 Volts or 240 Volts and 1 Phase Power
Automatic DynaTrol Control Panel with two 50 Amp Plug-In Circuits and with Branch Fusing.
Includes DynaTrol, panel, stand for panel, fuses, relays, power contactors, transformer and all other internal components.
Unit does not include a Power Cord.
This is used with all Two CIrcuit DaVinci X2800-D & XB2800-D, X3200-D & XB3200-D, T2300-D & TB2300-D, and T3400-D & TB3400-D Series Kilns at 208 Volts or 240 Volts and 3 Phase Power