June 20, 2025
|
|---|
SHOP KILN PARTS
M-V-MULT/00
$42.00
Vent-Sure Vent System Multi-Mounting Bracket - Unit attaches to the Wall Mount Bracket allowing for the Vent System to be mounted with the Outlet Duct pointed up and includes Assembly Hardware. The Dimensions are 8.75" tall, 10.25" wide and 8" deep. 
M-V-BRKT/00
$139.00
Vent-Sure Vent System Wall Mount Bracket - Unit includes a Motor Mounting Plate, an Output Mounting Plate, a 12" Long x 4" Diameter Output Pipe, and Assembly Hardware 
M-V-CNTL/PT
$200.00
The Vent Control allows you to automatically control the operation of the Vent-Sure kiln vent with one of the outputs from the DynaTrol (or Genesis). To see more details go the the Accessory Page here. 
M-V-VENT/PT
$775.00
The Vent-Sure automatic kiln vent helps prevent corrosion on the inside and outside of your kiln. It ensures that your kiln gets the longest possible life from your elements and electrical components. This is so important that, if you do not have a Vent-Sure installed on your kiln, the pro-rated element warranty is in a different category. An 8-foot flexible duct is included. We also sell a separate 15-foot flexible duct that you can purchase for longer runs. 
M-V-VENT/4P
$885.00
The Vent-Sure automatic kiln vent helps prevent corrosion on the inside and outside of your kiln. It ensures that your kiln gets the longest possible life from your elements and electrical components. This is so important that, if you do not have a Vent-Sure installed on your kiln, the pro-rated element warranty is in a different category. 
M-L-CORD/00
$4.55
Cord Caution Label - This label goes by the Power Cord and warns about keeping it away from the kiln case 
M-L-ELEC/00
$4.55
Electrical Hazard Label - This label goes inside the Control Box and warns about electrical shock, etc. 
M-L-HING/00
$4.55
Hinge Caution Label - This label goes on the side of the Hinge and warns about the use of the Locking Push Pin Assembly 
L-G-WIRE/16
$3.70
16 Gauge Wire, rated to 105C, cut to length specified by customer. 
L-G-WIRE/10
$3.70
White 10 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer. 
L-G-WIRE/14
$3.70
14 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer. 
L-G-WIRE/06
$3.70
6 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer. 
L-G-WIRE/08
$3.70
8 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer. 
E-X-1800/20
$70.00
Voltage:
208
Size (Diameter):
Gray (DaVinci only 1985-2004)
DaVinci X1800 Series 208 Volt/1 & 3 Phase Small Element (.41" Outside Diameter) - Used on All X1800 Kilns at this Voltage 
E-X-1800/30
$70.00
Voltage:
240
Size (Diameter):
Gray (DaVinci only 1985-2004)
DaVinci X1800 Series 240 Volt/1 & 3 Phase Small Element (.41" Outside Diameter) - Used on All X1800 Kilns at this Voltage 
F-X-18CR/00
$60.00
Corner Brick for DaVinci X1800 Series Kilns - Unit includes one Brick cut specifically for this Series (Four per Kiln) 
P-X-1800/BT
$495.00
DaVinci X1800-D & XB1800-D Bottom Firebrick Slab - Unit includes a cemented 3" Brick Slab wrapped in the Stainless Steel Band 
S-X-1800/00
$134.00
Stainless Steel Band for DaVinci X1800-D & XB1800-D Series Kiln Sections (Rings) - Unit includes Hose Clamps spot welded to and all appropriate holes punched in the Stainless Band and is used with All X1800-D & XB1800-D Series Kilns 
S-X-18T3/00
$66.00
Stainless Steel Band for DaVinci X1800-D & XB1800-D Series Kiln Tops or Bottoms - Unit includes Hose Clamps spot welded to the Stainless Band and is used with All X1800-D & XB1800-D Series Kilns 
P-X-1800/TP
$495.00
DaVinci X1800-D & XB1800-D Top Firebrick Slab - unit includes a cemented 3" Brick Slab wrapped in the Stainless Steel Band with Angle Clips. If you need new lid channels (metal c-channels on sides of lid), contact Service@hotkilns.com directly for special order - you will need these if you're converting from a fiber lid. 
F-X-23CR/QD
$65.00
Corner Brick for DaVinci X2300 Series Kilns - Unit includes one Brick cut specifically for this Series (Four per Kiln). This part number is for DaVinci Kilns with the Quad element option. There are four grooves. Also used on the e2318-XT & e2327-XT corner brick with Quad elements. 
E-X-2300/2L
$84.00
Voltage:
208
Size (Diameter):
Large- (.46" OD, 2004-Present)
DaVinci X2300 Series 208 Volt/1 & 3 Phase Large Element (.46" Outside Diameter) - Used on All X2300 Series Kilns at this Voltage with a Serial Number of or succeeding "060104-A" (Made on or after June 1, 2004) 
E-X-2300/2Q
$144.00
Voltage:
208
Size (Diameter):
Quad (Always Large Diameter)
DaVinci X2300 Series 208 Volt/1 & 3 Phase Quad Element (.46" Outside Diameter) - Used on All X2300 Series Quad Kilns at this Voltage 
E-X-2300/20
$84.00
Voltage:
208
Size (Diameter):
Gray (DaVinci only 1985-2004)
DaVinci X2300 Series 208 Volt/1 & 3 Phase Small Element (.41" Outside Diameter) - Used on All X2300 Series Kilns at this Voltage with a Serial Number preceding "060104-A" (Made before June 1, 2004)
E-X-2300/4Q
$144.00
Voltage:
220 or 380 3 Phase Wye
Size (Diameter):
Quad (Always Large Diameter)
DaVinci X2300 Series 220 1 Phase and 380V 3 Phase Wye Quad Element (.46" Outside Diameter) - Used on All X2300 Series Quad Kilns at this Voltage 
E-X-2300/4L
$84.00
Voltage:
220 or 380 3 Phase Wye
Size (Diameter):
Large- (.46" OD, 2004-Present)
DaVinci X2300 Series 220-380 Volt/1 & 3 Phase Large Element (.46" Outside Diameter) - Used on All X2300 Series Kilns at this Voltage (Non-U.S. Voltage) with a Serial Number of or succeeding "060104-A" (Made on or after June 1, 2004) 
E-X-2300/3L
$84.00
Voltage:
240
Size (Diameter):
Large- (.46" OD, 2004-Present)
DaVinci X2300 Series 240 Volt/1 & 3 Phase Large Element (.46" Outside Diameter) - Used on All X2300 Series Kilns at this Voltage with a Serial Number of or succeeding "060104-A" (Made on or after June 1, 2004) |
©2025 L&L Kiln Mfg Inc
https://hotkilns.com/pottery-kiln-parts/metal/misc-hardware
