Ceramic Element Connection Board for Kiln Sections with Three Elements - Unit includes terminal screw and all hardware.
SHOP KILN PARTS
SUBCATEGORIES
Ceramic Element Connection Block for M Series (middle section) Easy-Fire Kiln Sections - The unit includes the terminal screw, nuts, and stainless large flat washers. Used on e18M, e18M-3, e23M, e23M-3, e28M-3 middle kiln sections that are 4.5" high.
This is a set of components to move the cord connections on a DaVinci kiln ring to the outer element connection box.
The kit consists of:
- (1) Two Pole Terminal
- (1) Insulating board
- (2) Terminal Mounting Screws (#8 X 3/4" A Type
- (2) #10 SS nuts
- (2) #10 SS washers
- (2) #10 SS split washers
- (1) #10 X 1/2" Self-Tapping screw (ground screw)
- (1) #10 star washer (for the ground screw)
- (1) Ground Symbol Sticker
- (1) 12" length of wire insulator sleaving for covering the cord wires (this gets cut to length to slip over the cord wires)
- (2) 8 Gauge 150 Deg C 9" long Power Wires with a ring terminal to go the element connection and a stripped end to go in the new terminal block
Yellow Insulated Female Slip on Wire Terminal - Unit can accommodate up to 10-12 AWG and a 1/4" Spade, and is used on the Power Wires. (REF: E-TRM-640907-A4)
Typical use is on power wires that go from relays to terminal strips and from terminal strips to elements.
Blue Insulated Female Slip on Wire Terminal - Unit can accommodate up to 16-14 AWG and a 1/4" Spade, and is used on the Control Board, On/Off Switch, and Relays. (REF: E-TRM-640905-A3)
Blue Insulated Female Slip on Wire Terminal - Unit can accommodate up to 16-14 AWG and a 3/16" Spade, and is used on the Transformer Wiresand 1/2 Amp Panel Control Fuse Holder. (REF: E-TRM-640919-A3)
Red Insulated Female Slip on Wire Terminal - Unit can accommodate up to 22-18 AWG and a 3/16" Spade, and is used on the Thermocouple Wires. (REF: E-TRM-640917-A1)
Yellow Insulated Large Fork Terminal - Unit is a Flanged Spade Fork, can accommodate up to 12-10 AWG. Fits on a #10 stud. Used on Receptacles and Ground Wires. (REF: E-TRM-FNFTAP-A2)
Non-Insulated High Temperature Lug terminal - Unit is used for the Wire Leads of 50 Amp Power Cords ( 6 AWG) and can fit over a 1/4" Stud (REF: E-TRM-PS14RT-A1)
Non-Insulated Medium Ring Terminal - Unit can accommodate up to 12-10 AWG. #10 Stud size. Used for Element Power & Ground Wire Ends that go onto the Element Terminals and for Ground Wires. (REF: E-TRM-233457-A1)
Typical use is on 10 gauge power wires that go to elements.
MOV Surge Suppressor for 250 Volt / 50 Amp Enclosed Power Contactors - Unit is 5mm in Diameter, absorbs the discharge energy from the inductive coil of a contactor, and can be used on All 240 Volt or 208 Volt Contactors
The L-G-MOV1/00 MOV has a mark on it of PZ390 (you have to use a magnifying glass to see this).
Attach the MOV Suppressor to the Power Contactor by using two 16-14 AWG Insulated Female Slip on Wire Terminals for 1/4" Spades, one on each end of the MOV.
Insulated Piggyback Terminal - Unit is a Female Slip On with a Male Spade attached, can accommodate up to 16-14 AWG and a 1/4" Spade, and is used on Relays (REF: E-TRM-PIGBAK-A1)
Blue Insulated Small Fork Terminal - Unit is a Spade Fork, can accommodate up to 16-14 AWG. Fits on a #8 stud. It is used on Older 4-Way Switches. (REF: E-TRM-320862-A3)
Blue Insulated Small Ring Terminal - Unit can accommodate up to 16-14 AWG, a #10 Stud. Used for 15 Amp & 20 Amp Power Cord Wire Leads and for Ground Wires. (REF:E-TRM-236160-A1)
Set of Spade Wire Terminals that are used to connect wires to the 4-Way Arkless Input Switch.
Set of Spade Wire Terminals that are used to connect wires to the Robert Shaw INF Infinite Input Switch.