For use with No Crimp Ceramic Element Terminal Blocks.

Unit is 2-3/4" long and is terminated with two #10 Ring Terminals.

For use with Universal Ceramic Element Terminal Blocks.

Unit is 4-1/8" long and is terminated with two #10 Ring Terminals.

14 Pin Female Receptacle for Handheld Controls - Unit includes color coded wires for hook up in the Floor-Mounted Control Panel and is used in conjunction with the 14 Pin Male Plug

14 Pin Male Plug for Handheld Controls - Unit includes a 6' Long Cord with color coded wires at the end for hook up in the Handheld Box and is used in conjunction with the 14 Pin Female Receptacle

Control Wire Harness - All wires precut and terminated. 

All wires are color coded and the color coding corresponds to the wiring diagram

Control Wire Harness - Set of wires is precut and terminated for all three section Easy-Fire kilns.

Control Wire Harness - Set of wires is precut and terminated for all three section School-Master Kilns (SM23T, SM23T-3 & SM28T-3).

Control Wire Harness - Set of wires is precut and terminated for all Easy-Fire Kilns with two Sections.

This is a custom, made-to-order wire. Upon order, please specify:
 

1. LENGTH (inches)
    
2. WIRE GAUGE (all control wire is 16ga, approximately 1/8" outside-diameter)
   
    
3. TERMINAL (if any) on either end of the wire. These are the options:
   
    
4. COLOR (we will try our best to match)
    

This is a custom, made-to-order wire. Upon order, please specify:
 

1. LENGTH (inches)
    
2. WIRE GAUGE - measure your wire and refer to the following ranges of outer diameters:
   
    
3. TERMINAL (if any) on either end of the wire. These are the options:
   
    
4. COLOR (we will try our best to match, but cannot guarantee)
    

This is a custom, made-to-order wire. Upon order, please specify:
 

1. LENGTH (inches)
    
2. TERMINAL (if any) on either end of the wire. These are the options: 
   
    
3. Please confirm you are looking for YELLOW, Type-K TC wire

This is a custom, made-to-order wire. Upon order, please specify:
 

1. LENGTH (inches)
    
2. TERMINAL (if any) on either end of the wire. These are the options: 
   
    
3. Please confirm you are looking for GREEN, Type-S TC wire
    

This is a set of components to move the cord connections on a DaVinci kiln ring to the outer element connection box.

The kit consists of:

1.  (1) Two Pole Terminal
2.  (1) Insulating board
3.  (2) Terminal Mounting Screws (#8 X 3/4" A Type 
4.  (2) #10 SS nuts
5.  (2) #10 SS washers
6.  (2) #10 SS split washers
7.  (1) #10 X 1/2" Self-Tapping screw (ground screw)
8.  (1) #10 star washer (for the ground screw)
9.  (1) Ground Symbol Sticker
10.  (1) 12" length of wire insulator sleaving for covering the cord wires (this gets cut to length to slip over the cord wires)
11.  (2) 8 Gauge 150 Deg C 9" long Power Wires with a ring terminal to go the element connection and a stripped end to go in the new terminal block

Element Jumper Wires - Unit is precut and fitted with the appropriate terminal ends to run from the Element Terminal Block on the Bottom Section to the Element Terminal Block on the Top Section. Note: both wires are now white.

Ground Wire Jumper for Piggybacked Control Panels, such as Easy-Fire and eQuad kilns - Unit is 10 AWG, precut, and comes with two Ring Terminals

Set of wires is precut, terminated, and labeled to run from the Bottom Element Terminal Block to the Power Terminal Strip on all Two Section kilns, or from the Middle Element Terminal Block to the Power Terminal Strip on all Three Section Easy-Fire and School-Master Kilns. There are two wires in a set. Note: This is wire #3 and #4.

Set of wires is precut, terminated, and labeled to run from the Bottom Element Terminal Block to the Power Terminal Strip on All Three Section Easy-Fire and School-Master Kilns. There are two wires per set. Note: This is wire #5 and #6.

Power Wire Harness - Set of wires is precut, terminated, and labeled to run from the Power Connection Block to the Power Relays on all Easy-Fire and School-Master Kilns with three sections at any voltage and 1 Phase Power. There are six wires in a set.

Power Wire Harness - Set of wires is precut, terminated, and labeled to run from the Power Connection Block to the Power Relays on all Easy-Fire and School-Master Kilns with three sections at any voltage and 3 phase power. There are six wires in a set.

Power Wire Harness - Set of wires is precut, terminated, and labeled to run from the Power Connection Block to the Power Relays on all Easy-Fire Kilns with two sections at any voltage and 1 Phase Power. There are four wires per set.

Power Wire Harness - Set of wires is precut, terminated, and labeled to run from the Power Terminal Strip to the Power Relays on All Easy-Fire and School-Master Kilns with three sections at any voltage and phase power. There are six wires in a set.

Power Wire Harness - Set of wires is precut, terminated, and labeled to run from the Power Terminal Strip to the Power Relays on all Easy-Fire Kilns with two sections at any voltage and 1 Phase Power. There are four wires in a set.

This includes 6 high-temperature power wires that connect the terminal strip inside the panel to the elements. All terminals are included as an assembly. All wires are white.

This includes 8 high-temperature power wires that connect the terminal strip inside the panel to the elements. All terminals are included as an assembly. All wires are white.

Set of wires is precut, terminated, and labeled to run from the Top Element Terminal Block to the Power Terminal Strip on All Easy-Fire and School-Master Kilns. There are two wires per set. Note: This is wire #1 and #2.

Red Pilot Light - Unit is used for All Manual Kiln Control Panels