Cylindrical Ceramic Spacer - Unit is a 3/4" Diameter Cylinder x 1/4" High with a 1/4" Diameter hole in the center.

NOTE: These are also used to hold thick elements in place by using it as a wedge between the element and the ceramic holder. See this Knowledgebase page.

This is used to prevent element ends from touching each other (on older kilns). A 21/64" diameter hole is drilled into the brick 1-1/4" deep and the assembly is inserted into the hole. The overall length is 2" and the thick end is about 3/4" long.

Ceramic Element Terminal Block for Easy-Load kilns.

(NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Nov 1, 2025) - newer kilns need this block. Check your kiln before ordering. 

The unit includes the terminal screw, nuts, and stainless flat washers. Lock washers are no longer needed.

You may also need two mounting screws.

See this link for wiring help (diagrams at the bottom of page)

Ceramic Element Terminal Block for M Series (middle section) Easy-Fire Kiln Sections. Was used on e18M, e18M-3, e23M, e23M-3, e28M-3 middle kiln sections that are 4.5" high.

(NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Feb 1, 2025) - newer kilns need this block. Check your kiln before ordering. 

The unit includes the terminal screws, nuts, and stainless flat washers. Lock washers are no longer needed.

You may also need two mounting screws.

See this link for wiring help (diagrams at the bottom of page)

Ceramic Element Terminal Block for Kiln Sections with Three Elements - Unit includes two Terminal Screw Assemblies.

(NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Sep 1, 2024) - newer kilns need this block. Check your kiln before ordering. 

You may also need two mounting screws

See this link for wiring help (diagrams at the bottom of page)

Ceramic Element Terminal Block for Kiln Sections with Three Elements - Unit includes four Terminal Screw Assemblies.

(NO LONGER USED ON NEW KILNS AS OF APPROXIMATELY Sep 1, 2024) - newer kilns need this block. Check your kiln before ordering. 

You may also need two mounting screws

See this link for wiring help (diagrams at the bottom of page)

Ceramic Element Terminal Block for Kiln Sections with Two Elements - Unit includes three Terminal Screw Assemblies.

You may also need two mounting screws

See this link for wiring help (diagrams at the bottom of page)

Ceramic Element Terminal Block for Kiln Sections with Two Elements - Unit includes two Terminal Screw Assemblies.

You may also need two mounting screws

See this link for wiring help (diagrams at the bottom of page)

Ceramic Handle for 2nd Generation Easy-Lift Hinges - The unit is 1" in Diameter, 7-15/16" in Length, and Includes Mounting Hardware

Acorn Nuts: M-A-ACRN/00 - (two included)
Threaded Rod: M-A-TROD/00 - (one included)

Element Insulator Bushing - Unit is used in conjunction with the Old Style (Red) Element Terminal Boards to keep the Element insulated from the Sheet Metal Casing

Corderiete Ceramic Tube: Element Insulator Tube - 4" long 5/16" OD x 3/1"6 ID. Used in some front-loading kilns for insulated the element ends as they protrude throught he insulation.

Mullite Thermocouple Protection Tube - Unit is 5" Long x 1" Diameter with a stepped head for use with All Standard Length Type-K 8 Ga. Thermocouples. NOTE: This is the newer type open end tube which was put in service with new kilns starting in September 2020.

Mullite Thermocouple Protection Tube - Unit is 7" Long x 1" Diameter with a stepped head for use with all Longer Length Type-K 8 Ga. Thermocouples. NOTE: This is the newer type open end tube which was put into service for new kilns starting in November 2020.

Unit includes one block and two Terminal Screw Assemblies.

You may also need two mounting screws

You may also need this or this jumper wire. 

See this link for wiring help (diagrams at the bottom of page)

Ceramic Peep Hole Plug - Unit is a approximately 7/8" Diameter (.86") x 3.75" Long Top Hat Style Plug (Stepped Head has a 1.5" Diameter and serves as a heat lock)

Ceramic Peep Hole Plug - Unit is a 1" Diameter x 5" Long Top Hat Style Plug (Stepped Head has a 2" Diameter and serves as a heat lock)