For use with No Crimp Ceramic Element Terminal Blocks.

Unit is 2-3/4" long and is terminated with two #10 Ring Terminals.

For use with Universal Ceramic Element Terminal Blocks.

Unit is 4-1/8" long and is terminated with two #10 Ring Terminals.

6 Gauge Jumper Wire - Unit is 10" Long and includes two Ring Terminals

This is a set of components to move the cord connections on a DaVinci kiln ring to the outer element connection box.

The kit consists of:

1.  (1) Two Pole Terminal
2.  (1) Insulating board
3.  (2) Terminal Mounting Screws (#8 X 3/4" A Type 
4.  (2) #10 SS nuts
5.  (2) #10 SS washers
6.  (2) #10 SS split washers
7.  (1) #10 X 1/2" Self-Tapping screw (ground screw)
8.  (1) #10 star washer (for the ground screw)
9.  (1) Ground Symbol Sticker
10.  (1) 12" length of wire insulator sleaving for covering the cord wires (this gets cut to length to slip over the cord wires)
11.  (2) 8 Gauge 150 Deg C 9" long Power Wires with a ring terminal to go the element connection and a stripped end to go in the new terminal block

Element Jumper Wires - Unit is precut and fitted with the appropriate terminal ends to run from the Element Terminal Block on the Bottom Section to the Element Terminal Block on the Top Section. Note: both wires are now white.

Ground Wire Jumper for Piggybacked Control Panels - Unit is 10 AWG, precut, and comes with two Ring Terminals

High Temperature Wire Sleeving for DiVinci Kiln Jumper Wires - This material is used to provide an additional layer of insulation around the power wires in the Element Connection Box on All DaVinci Kilns.

Rated 316 C, 3/8" ID, Uncoated, silver natural color, Complies with VW-1 flammability requirements.

Insulating Sleeving for Cable Wire

Wire Sleeving for Jupiter Kiln Jumper Wires - The material is used to provide an additional layer of insulation around the Power Wires in the Element Connection Box on older Jupiter Automatic and Jupiter Manual Kilns.

105 DEG C. 600V, 3/16" nominal ID.

This includes 6 high-temperature power wires that connect the terminal strip inside the panel to the elements. All terminals are included as an assembly. All wires are white.

This includes 8 high-temperature power wires that connect the terminal strip inside the panel to the elements. All terminals are included as an assembly. All wires are white.

#10-24 Stainless Steel Hex Nut - Unit is used for mounting the Vent Bypass Box and Contactor Plates and for the Element Terminal Bolts

Green 10 Gauge High Temperature Wire (made to order) is no longer available. Please use 10 ga white wire.

White 10 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer, and terminated with terminals specified by customer. 

Black 14 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer, and terminated with terminals specified by customer.

Green 14 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer, and terminated with terminals specified by customer. 

Red 14 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer, and terminated with terminals specified by customer. 

White 14 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer, and terminated with terminals specified by customer.

Black 6 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer, and terminated with terminals specified by customer. 

Green 6 Gauge High Temperature Wire, rated to 150C, cut to length specified by customer, and terminated with terminals specified by customer. 

Black 10 Gauge High Temperature Wire is no longer available. Please use 10 ga white wire.